"Device does not accept mode command"

All questions about how to use KryoFlux go here.
MultiDisk
Posts: 14
Joined: Wed Jan 26, 2011 3:41 pm

"Device does not accept mode command"

Post by MultiDisk » Sat Feb 04, 2012 7:40 pm

Hi..

While chewing thru many disks with my automated disk robot.. I've noticed occasionally that the Kryoflux ends one disk, but when asked to process the next, fails with "Device does not accept mode command". This is infrequent, and seems to occur after reading at least 20+ disks in a row..

It then stays in this state until I reset it by disconnecting/reconnecting the USB cable..

Any suggestions ?

User avatar
mr.vince
Posts: 1873
Joined: Tue Oct 05, 2010 5:48 pm

"Device does not accept mode command"

Post by mr.vince » Sat Feb 04, 2012 7:44 pm

Which state is the board in when this happens? LEDs?

MultiDisk
Posts: 14
Joined: Wed Jan 26, 2011 3:41 pm

Re: "Device does not accept mode command"

Post by MultiDisk » Mon Feb 27, 2012 1:59 pm

Over 2500 disks later.. I haven't narrowed it down much.. also have been rather slack & not checked the LEDs on the repeats.. but I have found that the sequence of power up seems to affect how likely it is to occur. If I power up the drive after the kryoflux, then it'll happen within 20 disks or so, if I connect usb to kryoflux, then power up the drive, then disconnect, and reconnect the usb to the kryoflux, I can read 500+ disks sequentially without issue.

Congratulations on building a bit of kit that survived reading that many disks =) (and that likely survived my abuse of powering it up in odd orders).

It ran for 12 hrs a day, days at a time to read through that many.. writing stream format, & adf (where possible.. )

Guy90
Posts: 1
Joined: Tue Mar 20, 2012 11:46 am

Re: "Device does not accept mode command"

Post by Guy90 » Wed Mar 21, 2012 8:12 am

I'm struggling with the same issue right now. I have to record 50 disks for my scientific research work but apparently Kryoflux shows me this bug...I've tried a couple of tricks to fix it but they all turned out to be a failure...Have you managed to fix it?

User avatar
IFW
Posts: 2634
Joined: Mon Nov 08, 2010 2:42 pm

Re: "Device does not accept mode command"

Post by IFW » Wed Mar 21, 2012 11:29 am

Just retry or reset the board.

User avatar
mr.vince
Posts: 1873
Joined: Tue Oct 05, 2010 5:48 pm

"Device does not accept mode command"

Post by mr.vince » Wed Mar 21, 2012 3:56 pm

Is the board powered?

User avatar
mr.vince
Posts: 1873
Joined: Tue Oct 05, 2010 5:48 pm

"Device does not accept mode command"

Post by mr.vince » Tue Apr 03, 2012 8:40 pm

Hello?

Jazz Jackrabbit
Posts: 2
Joined: Wed Nov 18, 2015 9:50 am

Re: "Device does not accept mode command"

Post by Jazz Jackrabbit » Mon Jan 23, 2017 6:01 pm

Have the same Problem right now. Any News how to fix it?

User avatar
mr.vince
Posts: 1873
Joined: Tue Oct 05, 2010 5:48 pm

Re: "Device does not accept mode command"

Post by mr.vince » Tue Jan 24, 2017 7:08 am

If you can give a proper description of your problem we'll be delighted to help you.

Jazz Jackrabbit
Posts: 2
Joined: Wed Nov 18, 2015 9:50 am

Re: "Device does not accept mode command"

Post by Jazz Jackrabbit » Mon Jan 30, 2017 10:36 pm

Its The same error like in this post "Device does not accept mode command". But for me after connecting and disconnect the device a few times it works.

Post Reply

Who is online

Users browsing this forum: No registered users and 1 guest